What is a Mitsubishi Pajero V80 airbag control unit?
The Mitsubishi Pajero V80 airbag control unit is the central safety unit that activates all occupant restraint systems in the event of an accident. It precisely monitors sensors, stores crash data, and ensures the proper functioning of all airbag modules and seatbelt pretensioners. A professional Mitsubishi Pajero V80 airbag control unit repair restores system integrity.
This electronic control unit, also known as the SRS module, analyzes signals from various crash sensors.
Its primary function is to accurately detect collisions and coordinate the deployment of airbags and seatbelt pretensioners.
The module performs continuous self-monitoring of the entire airbag system, with any detected malfunction activating a warning light on the dashboard indicating the need for diagnosis or repair .
After an accident or significant malfunction, the device stores important crash data and specific error codes. This information is essential for diagnostics and the necessary reset service to restore the module to its original state.
Why is the Mitsubishi Pajero V80 airbag control unit defective?
A Mitsubishi Pajero V80 airbag control unit often fails because it stores crash data after an accident, preventing further use, or due to internal electronic failures. Faulty circuits, communication problems, or external influences can also cause failure. This makes a professional Mitsubishi Pajero V80 airbag control unit repair essential.
After a collision, the control unit stores indelible crash data, even if no airbags are deployed. This data blocks further system function, requiring replacement or a professional reset service.
Internal components such as EEPROM, ROM, or RAM can become faulty over time or be damaged by overvoltage. This leads to internal control unit errors that can compromise the system's safety function.
Problems with CAN bus communication can also lead to failure, as the control unit cannot receive or send data from other vehicle systems. A thorough diagnosis is then essential to repair a defective module.
Common error codes for Mitsubishi Pajero V80 airbag control unit repair
Common error codes for Mitsubishi Pajero V80 airbag control unit repairs indicate specific problems within the control unit, including internal memory errors, communication problems, or defective activation circuits. These codes are crucial for accurate diagnosis and identifying the necessary repair or module reset.
- B1404: Driver airbag (1st squib) activation circuit shorted → Possible cause: Internal circuit fault or wiring problem in the control module.
- B1434: Side airbag (left) activation circuit shorted → Possible cause: Fault in the internal activation circuit of the control unit or short circuit to ground.
- B1435: Side airbag (left) activation circuit interrupted → Possible cause: Interruption in the control unit's internal circuit or signal path to the airbag.
- B1492: Passenger airbag (2nd squib) short to ground → Possible cause: Internal control unit error or unwanted short to ground in the module.
- B1493: Passenger airbag (2nd squib) short circuit to supply voltage → Possible cause: Internal error in the control unit, which leads to a short circuit to the supply voltage.
- B1494: Passenger airbag (2nd squib) activation circuit shorted → Possible cause: Fault in the ignition circuit of the control unit for the passenger airbag.
- B1495: Passenger airbag (2nd squib) activation circuit open → Possible cause: Open circuit in the internal circuit of the control unit that activates the airbag.
- B1496: SRS-ECU non-volatile memory (EEPROM) error → Possible cause: Defect in the control unit's EEPROM, which requires repair or reset.
- B1497: SRS-ECU front activation integrated circuit faulty → Possible cause: Defect in the central processor or ASIC of the control unit.
- B1498: SRS-ECU ROM or RAM error → Possible cause: Internal memory defect in the control unit that affects data processing.
- B1499: Collision decision (crash detection) → Possible cause: Internal error in the control unit logic responsible for accident detection.
- B1509: Wrong SRS-ECU control unit detected → Possible cause: Incompatible or incorrectly programmed control unit was installed.
- B1519: SRS-ECU connector does not lock properly → Possible cause: Physical problem at the control unit connector that interrupts the connection.
- B1547: Passenger airbag deactivated → Possible cause: Control unit registers a deactivation of the passenger airbag, often due to a switch fault.
- B1548: CAN bus communication impossible → Possible cause: Serious communication error of the control unit in the vehicle network, causing a failure .
- B1549: CAN bus communication error → Possible cause: General fault in the data transmission of the control unit via the CAN bus.
What part numbers are available for the Mitsubishi Pajero V80 airbag control unit repair?
Three precisely verified OEM part numbers are relevant for the Mitsubishi Pajero V80 airbag control unit repair: 8635A093, MR551782, and P21516708. Correct identification is crucial to ensure compatibility with your Mitsubishi Pajero IV (V80) and enable a successful repair or replacement.
These specific part numbers have been validated multiple times by independent sources as genuine airbag control units for the Mitsubishi Pajero IV V80 series. They ensure that the replacement or repair module is a perfect fit for the vehicle's systems.
Numbers such as 8635A093, MR551782, and P21516708 are intended exclusively for this generation of airbag control units. Other numbers that represent ABS control units or airbag coil cables are incompatible and were excluded during diagnosis .
Before repairing or replacing a control unit, the existing part number of the defective module should be checked. This prevents incorrect purchases and ensures the full functionality of the security system.