What is a Subaru Legacy BE airbag control unit?
The Subaru Legacy BE airbag control unit is the central safety unit in the Supplemental Restraint System (SRS), responsible for monitoring and activating all occupant protection systems in the event of a crash. It processes sensor data, stores important event data, and ensures the precise deployment of airbags and seatbelt pretensioners to guarantee the safety of vehicle occupants.
This module is crucial for crash detection by interpreting signals from various acceleration and impact sensors in the Subaru Legacy BE.
It initiates the deployment of front, side and, if applicable, curtain airbags as well as seat belt pretensioners based on the severity of the detected collision.
The system also has built-in self-diagnostic functions that continuously monitor its integrity and signal malfunctions via a warning light on the dashboard.
Why is the Subaru Legacy BE airbag control unit defective?
A Subaru Legacy BE airbag control module can be **defective** because it permanently stores crash data after an accident, causing it to lock up, or due to internal electronic errors such as power surges and component failures. This often leads to **failure** of the airbag systems and requires professional **repair** or replacement to restore vehicle safety.
Common causes of **failure** include stored crash data after a collision, which renders the control unit unusable until it is reset or replaced.
Internal component failures such as defective EEPROM memory, calibration errors or communication problems in the CAN bus can also cause the module to **break**.
Problems with the power supply or even exposure to moisture can affect the electronics and a **diagnosis** indicate a control unit fault.
Common error codes for Subaru Legacy BE airbag control unit repair
When repairing a Subaru Legacy BE airbag control unit, specific error codes are crucial. They point directly to internal problems with the control unit, not sensors or other components. These codes facilitate diagnosis and indicate problems such as communication failures, internal memory errors, or module calibration errors, allowing for targeted troubleshooting.
- B1000 → Control unit communication error → Signals disruptions in the communication between the airbag ECU and other vehicle systems.
- B1200 → Airbag control unit internal error → Indicates a general internal hardware or software error in the module.
- B1235 → Airbag control unit memory error → Indicates damage or inconsistency in the internal data memory.
- B1240 → Control module calibration error → Means that the module's internal calibration data is faulty or missing.
- B1260 → Internal EEPROM error in the airbag control unit → Indicates a problem with the control unit's non-volatile memory.
- B1270 → Airbag control unit memory error (checksum) → A checksum error in the memory indicates data corruption in the module.
- B1300 → Data bus communication (CAN) error → Communication error via the vehicle's Controller Area Network bus.
- B1400 → Control unit power supply error → A problem with the power supply to the airbag control unit, possibly due to low voltage.
- B1872 → Control unit detects defective airbag cushion (e.g. driver/passenger side) → The module reports a problem with a connected airbag cushion.
- B1877 → Airbag control unit error due to faulty airbag cushion connections → A fault caused by a poor electrical connection to the airbag cushions.
What part numbers are available for the Subaru Legacy BE airbag control unit repair?
For the **Subaru Legacy BE airbag control unit repair**, knowing the exact original part number is essential to ensure compatibility and system integrity. The correct part number prevents false activation or system malfunctions and ensures that the replacement part or repaired module can be seamlessly integrated into the existing SRS system.
The OEM part numbers for the Subaru Legacy BE airbag control module include: 98221AJ15B (replaces 98221AJ15A), 98221AE19A, 98221AC061 (replaces 98221AC060) and 98221AE08A.
Other verified original numbers are 98221AC080, 98221AN00E (replaces 98221AN00D), 98221AE01A and 98221AG260.
These numbers identify specific genuine Subaru parts that are precisely tailored to the Legacy BE series.
When repairing or replacing the part, it is essential to ensure that the part number exactly matches the original number, as modules are programmed specifically for each vehicle.
The **workshop** or specialist will thoroughly check compatibility before installation to ensure safe operation of the airbag system.