What is a Honda Passport 2nd Gen airbag control module?
The Honda Passport 2nd Gen airbag control unit is your vehicle's central safety unit, activating all occupant restraint systems in the event of an accident. It continuously monitors a variety of sensors, stores relevant crash data, and ensures precise deployment of the airbags and seatbelt pretensioners to maximize occupant safety.
This control unit, also known as the SRS module (Supplemental Restraint System), is responsible for controlling the passive safety systems.
It acts as the brain of the airbag system and processes sensor data at lightning speed to take the appropriate protective measures in an emergency.
Why is the Honda Passport 2nd Gen airbag control unit defective?
A Honda Passport 2nd Gen airbag control unit may be defective because it permanently stores crash data after an accident that needs to be erased, or because internal electronic components fail due to age or damage. A defect often manifests itself as an illuminated airbag warning light in the dashboard, preventing the entire safety system from functioning properly.
The most common cause of a defect is the storage of so-called "hard codes" or crash data after the airbag has been deployed.
Internal faults in the SRS module itself, caused by voltage fluctuations or material fatigue, can also lead to failure.
In such cases, a Honda Passport 2nd Gen airbag control unit repair is necessary to restore functionality and clear the warning light.
Common error codes for Honda Passport 2nd Gen airbag control unit repair
During Honda Passport 2nd Gen airbag control module repair, specific error codes occur that indicate problems directly within the control module itself, not with peripheral sensors or seatbelt pretensioners. These codes signal internal defects, communication failures, or problems with the warning light circuit that require professional diagnosis and repair of the module.
- B1000 → Control unit communication error → Signals a general problem in the communication of the airbag control unit with other systems or internal processes.
- 87-31 → Internal error in the SRS control unit → Indicates a malfunction or defect within the hardware or software of the airbag control unit.
- 91-1x → Internal system error of the SRS control unit → Describes various internal malfunctions of the airbag control unit that affect its operational capability.
- 91-2x → Short circuit in the SRS indicator circuit → Indicates that there is a short circuit in the airbag warning light circuit, which is reported directly by the control unit.
What part numbers are available for the Honda Passport 2nd Gen airbag control unit repair?
For Honda Passport 2nd Gen airbag control unit repair, it is crucial to identify the exact part number of the original module, as this is vehicle-specific and successful repair is only possible with matching components. A common OEM part number from Honda itself is 77960-TGS-A01, which can be used as a reference.
The specified part number 77960-TGS-A01 is a genuine Honda part number.
Specific part numbers from suppliers such as Bosch, Continental or Autoliv can usually only be found via extended databases and are not publicly listed.
Correct identification of the part number is essential because each airbag control unit is programmed to the vehicle identification number (VIN) and must match for proper function.
What does the Honda Passport 2nd Gen airbag control unit repair include?
Honda Passport 2nd Gen airbag control unit repair typically involves professionally erasing crash data and hard codes stored in the module after an accident. This service, often referred to as a "reset service," prepares the original control unit for reinstallation, restores its full functionality, and is a cost-effective alternative to replacing it with a new part.
The repair process ensures that all internal errors are cleared and the module is diagnosable again.
The control unit is cleaned, tested and prepared for use in the 2nd generation Honda Passport.
This service is particularly advantageous because the original module is retained, avoiding compatibility issues due to VIN programming.
Honda Passport 2nd Gen Airbag Control Unit Installation Location and Compatibility
The Honda Passport 2nd Gen airbag control unit is typically located centrally in the passenger compartment, often under the driver's seat or center console, to ensure short signal paths to all safety sensors and airbags. Its compatibility is strictly limited to 2nd generation Honda Passport models (approximately 2019 to 2026) and the specific vehicle VIN to ensure safe operation.
Before removing and installing the module, the vehicle battery must be disconnected to prevent accidental deployment of the airbags.
The control unit connects to airbags, belt pretensioners, impact sensors and the airbag warning light via multiple connectors.
It is critical that a repaired or replaced module exactly matches the year and model of the Honda Passport 2nd Gen to ensure the correct functioning of the complex security system.