What is a Ford Probe Mk2 airbag control unit?
The Ford Probe Mk2 airbag control unit is your vehicle's central safety unit, deploying all occupant restraint systems, such as airbags and seatbelt pretensioners, in the event of an accident. It continuously monitors the impact sensors and stores important crash data to ensure maximum protection and system functionality in an emergency.
This essential component is responsible for the safety of vehicle occupants. It receives signals from various crash sensors distributed throughout the vehicle.
In the event of a collision of sufficient severity, the control unit processes the sensor information at lightning speed. It then sends electrical impulses to the airbag gas generators, which then deploy the airbags within milliseconds.
Why is the Ford Probe Mk2 airbag control unit faulty?
A Ford Probe Mk2 airbag control unit often fails because it stores crash data after an accident, forcing the system to deactivate, or because internal electronic errors occur due to aging or voltage fluctuations. These internal errors lead to airbag system failure, which renders the safety function unsafe.
Common reasons for failure are internal errors such as cold solder joints or damaged components in the control unit itself. These can cause the airbag warning light to remain permanently illuminated.
After an accident, immutable crash data is stored in the Ford Probe Mk2 airbag control unit. This data prevents the system from functioning again, even if the unit is mechanically intact, and must be erased to reactivate the airbag system.
Low battery voltage or short circuits in the airbag circuitry can also affect the control unit and trigger a fault. A Ford Probe Mk2 airbag control unit repair efficiently resolves these problems.
Common error codes for Ford Probe Mk2 airbag control unit repair
During a Ford Probe Mk2 airbag control unit repair, specific error codes may occur that indicate internal problems with the control unit or its immediate environment, affecting system integrity. Diagnosing these codes is crucial to restoring the airbag system to full functionality and ensuring safety.
- Code 12: Low battery voltage → System voltage too low → Check external power source.
- Code 13: Short circuit to ground in the airbag circuit or crash sensor → Open circuit or short circuit → Check wiring and sensors.
- Code 21: Safing sensor incorrectly installed → Sensor not positioned correctly → Check the installation position of the safing sensor.
- Code 22: Safing sensor output shorted to battery → Defect in sensor or short circuit → Check safing sensor and wires for short circuit.
- Code 23: Safing sensor supply or return open → Open circuit → Check the wiring of the safing sensor.
- Code 24: Line 944B open / crash sensor low resistance → Defect in the line or in the crash sensor → Check line and crash sensor for continuity and resistance.
- Code 32: Driver airbag/safety sensor high resistance or open → Open circuit in airbag circuit → Check wiring or airbag module.
- Code 33: Pin 7 on the diagnostic monitor not grounded → Missing ground connection → Check ground connection on the diagnostic monitor.
- Code 34: Driver airbag/safety sensor low resistance or shorted → Short circuit in airbag circuit → Check wiring or airbag module.
- Code 35: Low resistance at pins 8 and 9 of the diagnostic monitor → Internal control unit error → Check the diagnostic monitor for internal defects.
- Code 51: Internal diagnostic monitor fuse blown → Internal control unit error → Check fuse in diagnostic monitor or repair control unit.
- Code 52: Backup power supply error → Battery or capacitor defective → Check backup power supply.
- Code 53: Internal error in the diagnostic monitor (ECU) → Control unit itself is defective → Control unit must be repaired or replaced.
What part numbers are available for the Ford Probe Mk2 airbag control unit repair?
For the Ford Probe Mk2 airbag control unit repair, specific OEM part numbers are relevant, ensuring exact compatibility with your vehicle model. These genuine Ford part numbers confirm that the part is the correct airbag control unit and not other components of the SRS system, which is crucial for a successful repair.
The following OEM part numbers are verified exclusively for the Ford Probe Mk2 Airbag Control Unit:
- F2AF-14B056-AD
- F2AF-14B056-BD
- GA2A677F0A
- F52Z61044A74AAC
- F42Z61044A74AAA
- F62Z-61044A74-AAB
- F32Z61043B13B
These numbers are crucial when having your Ford Probe Mk2 airbag control unit repaired. They ensure that the replaced or repaired module is a perfect fit for your vehicle.
Benefits of Ford Probe Mk2 Airbag Control Unit Repair
The Ford Probe Mk2 airbag control unit repair offers a cost-effective and environmentally friendly alternative to purchasing a new unit by preserving the vehicle-specific software and programming. This allows for a quick restoration of full system functionality without the need for complex reprogramming and contributes to sustainability, rather than purchasing expensive new parts.
A repair is usually significantly cheaper than purchasing a new control unit. This saves you considerable money, especially with an older model like the Ford Probe Mk2.
The vehicle-specific software and coding are retained during a professional repair. This eliminates the need for complex reprogramming of the control unit in the vehicle, saving time and additional costs.
By repairing your existing control unit, you actively contribute to environmental protection by reducing the amount of electronic waste generated. It's a sustainable solution for the failure of this important component.
Installation position and technical specifications of the Ford Probe Mk2 airbag control unit
The Ford Probe Mk2 airbag control unit is typically located in the passenger compartment under the seat or in the center console and acts as the heart of the SRS system, processing sensor data and deploying the airbags in an emergency. It communicates with the vehicle's sensors and airbags via multi-pin connectors to ensure reliable safety.
The airbag control unit is the central control unit of the SRS system. It continuously monitors all connected sensors and the airbag circuits.
In the Ford Probe Mk2, the control unit is usually located inside the vehicle to protect it from external influences. The exact location may vary depending on the vehicle's equipment, but is usually centrally located.
It features multiple connectors for the acceleration sensors, the airbags (driver and passenger), and the power supply. The special yellow airbag connectors ensure a secure and unmistakable connection.
Compatible Ford Probe Mk2 models and years for airbag control unit repair
The Ford Probe Mk2 airbag control unit repair is specifically designed for model years 1993 to 1997 that were equipped with airbags as standard and use the listed OEM part numbers. This repair is suitable for all Probe Mk2 engines that meet the airbag system requirements.
The airbag control unit is designed for the Ford Probe Mk2 (also known as Probe II) from 1993 to 1997. This includes the late Mk2 models that had a standard airbag system.
It's compatible with various engines, including the 2.2-liter four-cylinder (GL/LX/GT Turbo) and the 3.0-liter V6 (Vulcan engine). It's important that the vehicle is equipped with the appropriate airbag modules.
Driver airbags became standard around 1993, and passenger airbags often followed in 1994. The repair relates to the control units that support these configurations.