What is an Audi S8 D2 airbag control unit?
The Audi S8 D2 airbag control unit is the central safety unit that activates all occupant restraint systems in the event of an accident. It precisely monitors crash sensors, processes data at lightning speed, and deploys the appropriate airbags and seatbelt pretensioners to ensure optimal protection, while simultaneously storing important crash data.
This module acts as the "brain" of the passive safety system in your Audi S8 D2 and Audi A8 D2.
It integrates data from various sensors, including impact and seat occupancy sensors, to ensure targeted airbag deployment.
A functioning control unit is crucial for driving safety and compliance with legal regulations.
Why is the Audi S8 D2 airbag control unit defective?
The Audi S8 D2 airbag control unit can be defective due to internal component failure, unstable supply voltage, or irreversible crash data stored after an accident. This often results in the airbag warning light remaining permanently illuminated and the safety systems no longer functioning reliably.
Typical signs of a defect are a permanently illuminated airbag warning light or specific error codes that cannot be erased.
Common causes are internal short circuits, an incorrect or missing vehicle identification number (VIN) in the control unit, or damage caused by age and moisture.
In many cases, a repair of the Audi S8 D2 airbag control unit is possible to correct these malfunctions.
Common error codes for Audi S8 D2 airbag control unit repair
Typical error codes for the Audi S8 D2 airbag control unit directly indicate problems with the internal electronics, the power supply, or the module's diagnostic capabilities. These specific codes often indicate that the control unit itself is defective, requiring repair or replacement, as they cannot be erased.
- 1025 → Diagnostic light malfunction → Internal error in the control unit status, impairs the diagnostic function.
- 00532 → Supply voltage too low → Problems with the electrical power supply of the airbag control unit.
- 006535 → Control unit defective → A direct, serious defect in the airbag control unit that impairs its function.
- 00588 → Igniter resistance too high → An internal error regarding the ignition resistance detected by the control unit.
These error codes are manufacturer-specific for the VAG Group and directly indicate problems with the airbag ECU.
What part numbers are available for the Audi S8 D2 airbag control unit repair?
Several specific OEM part numbers are relevant for Audi S8 D2 airbag control unit repairs, covering various versions and years of manufacture. These genuine parts, manufactured by Audi and Bosch, ensure full compatibility and functionality with your vehicle, allowing for a precise replacement part search.
The following part numbers are verified as genuine parts for the Audi S8 D2 airbag control unit:
- 4D0959655C
- 4D0907474
- 4D0907389E
- 4D0959655H
- 4D0959655T
These variants, often with final letters such as C, H, T or E, are assigned to specific model years or engine configurations of the Audi S8 D2 and A8 D2.
Bosch is the main supplier of these control units, so corresponding Bosch part numbers such as 0285001150 or 0285001309 can often be found in conjunction with the Audi part numbers.
Installation position and connections on the Audi S8 D2 airbag control unit
The Audi S8 D2 airbag control unit is typically located under the center console, often under the carpet near the driver's seat. It features specific, usually yellow, multi-pin connectors that ensure precise communication with airbags, sensors, and vehicle electronics, and requires careful installation.
To gain access to the control unit, the center console usually has to be removed and the carpet may have to be lifted or cut open.
The connectors are usually bright yellow and equipped with 2-3 gold pins to ensure a correct and rust-free connection.
All work on the airbag system, especially the installation of the Audi S8 D2 airbag control unit, should only be carried out by qualified personnel to avoid safety risks.
Compatibility and technical specifications of the Audi S8 D2 airbag control unit
The Audi S8 D2 airbag control unit is specifically designed for Audi S8 and A8 models of the D2 series (approximately 1994–2002), with various part numbers optimized for specific model years and engine variants. These genuine parts guarantee maximum reliability and seamless integration into your vehicle's existing safety system.
The control unit is compatible with the Quattro variants and the V8 petrol engines as installed in the S8 D2 and A8 D2.
It monitors various crash sensors (front, side) and, depending on the equipment, can also detect seat occupancy in order to trigger airbags in a targeted manner.
The service life and reliability of the airbag control units for the Audi S8 D2 meet the high manufacturer standards and are designed for long-term functionality.